godin guitar serial number lookup electric

I took a small screwdriver and carefully wedged it between the 5&6 saddles and barely put pressure. When I would touch just the A string that hum would intensify greatly.

The guitar had an electrical buzz, fluorescent light type. The A string had sound, but it was far less than the other strings. It was a bizarre problem, like a ground problem. The only other consideration is that the 9v is not making it to the preamp or the preamp has a bad solder joint or connection.Īnyone who can shed some light on this would be greatly decided, since I was getting nowhere trying to get tech help, to take the leap and try to remove the saddle of the A string on mine. I suspect there is either a bad connection between the 9v and the jack ( unlikely) or that the circuit board where the jack is has a fault, or the jack itself is not passing the battery signal. I have cleaned it with deoxit and cleaned inside the jack with steel wool, which so far has not fixed the problem. I suspect the jack, which apparently disconnects the signal path for the 9v when unplugged, has a problem. I suspect that the 9v batter is merely to drive the preamp when the synth is not plugged in. The synth works whether there is a battery in the guitar or not, and the output to an amp works with the synth active. Which leads to the first question:Īre the saddles hard wired to the piezo or d they rest on it? If so is it safe to remove them and clean them as well as clean the piezo and saddle rest with some Doxit and a Qtip?Ģ) The 1/4' output only works when the synth is plugged in. 1) the Saddles are apparently a bit oxidized or otherwise corroded, I had a ground problem or some other contact problem with one and solved the problem by putting pressure on the saddle. I don't buy things from companies that are hard to contact, and the first thing I do with any major purchase is to find and call their tech number to see if they do indeed have real support.Īnyone knowledgeable about these problems please help me out. It seems they do not have a phone number to call for tech support. I have decided I do not, because I can find little tech support for their instruments, either in the literature that came with the guitar or on line. It was a test, buying it used, to see if I wanted other Godin products. I do like the guitar, it has problems though. I have some questions about a used Multiac I recently aquired.įirst off, I bought this as a test guitar to see how I liked Godins, have been considering a new Godin electric and/or acoustic electric. If anyone knows where I could find this, I would appreciate it very much! With that said, it would be super helpful to find a wiring diagram for this model, and/or interior pictures of the wiring. Provided I can source the necessary parts, I'm fairly confident that I can do the work myself (but should that prove to not be the case, I won't hesitate to bring it to a qualified tech). I've emailed Godin to ask whether they can provide the parts for this project, and have yet to hear back from them. It sounds fine and the work was done nicely, but I'd like to bring it back (or closer) to its original electronic state. However, the guitar I bought was bastardized at some point: the original preamp and piezo pickups were removed (replaced with a split saddle), the pickup was replaced with a humbucker, which was wired to an aftermarket preamp with EQ and built-in tuner. The preamp setup allows any of these sources to be played independently or blended together in any combination-thus the Spectrum moniker. Vendetta 3.I recently acquired a Godin Multiac Spectrum SA, which, when stock, comes with a lipstick neck pickup (ala the Multiac Steel), the per-string piezo pickups, which also feed a hex converter that outputs to a 13 pin synth connector. There were some bolt on USA and Czech models. They did start putting a year # somewhere in them, but they are imports and the year really doesn't matter for their worth. The Korean and Chinese guitar serials for the most part don't give a year or any other indication.

There are Czech Republic guitars that will have Hand Crafted in the Czech Republic on the back of the headstock with a serial # (nothing to denote year.) In the late 90's (1996 I believe) the serial #'s for the USA models were stamped on the fret board after the last fret. Try making a post on the Dean board - lots of knowledgeable folks.įor the most part - the USA models will have 'Made in the USA' with YY - SERIAL on the back of the headstock. Im looking, but Im not finding anything there either.

Godin guitar serial number lookup electric